[HTCondor-users] åå: Condor_submit: job cannot excute in the second node

["Zeng, Xinjie (zengxe)" <xinjie.zeng@xxxxxxxxxxxxxx>]

Hi Christoph,

Thank you for your quick reply!

 

I tried to submit 66 jobs again and I check the condor_q -better-analyze 9.

The output is :

â

Job 9.063 defines the following attributes:

 

ÂÂÂ DiskUsage = 10000

ÂÂÂ FileSystemDomain = "domian.com"

ÂÂÂ ImageSize = 10000

ÂÂÂ RequestDisk = DiskUsage

ÂÂÂ RequestMemory = ifthenelse(MemoryUsage =!= undefined,MemoryUsage,(ImageSize + 1023) / 1024)

 

The Requirements _expression_ for job 9.063 reduces to these conditions:

 

ÂÂÂÂÂÂÂÂ Slots

Step Matched Condition

-----Â --------Â ---------

[0]ÂÂÂÂÂÂÂÂ 192Â TARGET.Arch == "X86_64"

[1]ÂÂÂÂÂÂÂÂ 192Â TARGET.OpSys == "LINUX"

[3]ÂÂÂÂÂÂÂÂ 192Â TARGET.Disk >= RequestDisk

[5]ÂÂÂÂÂÂÂÂ 192Â TARGET.Memory >= RequestMemory

[8]ÂÂÂÂÂÂÂÂ 192Â TARGET.HasFileTransfer

 

 

009.063:Â Job is running.

 

Last successful match: Tue Jun Â2 02:26:21 2020

 

 

009.063: Run analysis summary ignoring user priority. Of 192 machines,

ÂÂÂÂÂ 0 are rejected by your job's requirements

ÂÂÂÂÂ 0 reject your job because of their own requirements

ÂÂÂÂ 64 match and are already running your jobs

ÂÂÂÂÂ 0 match but are serving other users

128 are able to run your job

 

It seems like all works fine, but they still didnât execute in another computers. In one machine I has 64 core so they actually all run within one machine. Also, I only can see 64 jobs here but I had 66 jobs. In condor_q, I found 2 jobs were done, but I donât think it could be done in seconds/

 

Warm Regards

Xinjie Zeng

 

åää: Beyer, Christoph
åéæé: 2020å6æ2æ 1:52
æää: htcondor-users
äé: Re: [HTCondor-users] Condor_submit: job cannot excute in the second node

 

Hi,

 

if you send a 'lot' of jobs you can check on an idle job with condor_q -better-analyze <jobid> or condor_q -analyze <jobid> there you will see the number of potential nodes this job could technically run on.

 

Once you discovered that it can only run on one machine you can check why it is not able to run on a specific machine using:

 

condor_q -better-analyze <jobid> -reverse -machine <nodename> (<nodename> needs to be fqdn here for some reason)

 

Best

christoph

 

--
Christoph Beyer
DESY Hamburg
IT-Department

Notkestr. 85
Building 02b, Room 009
22607 Hamburg

phone:+49-(0)40-8998-2317
mail: christoph.beyer@xxxxxxx

 

Von: "Xinjie Zeng" <xinjie.zeng@xxxxxxxxxxxxxx>
An: "htcondor-users" <htcondor-users@xxxxxxxxxxx>
Gesendet: Dienstag, 2. Juni 2020 05:19:45
Betreff: [HTCondor-users] Condor_submit: job cannot excute in the second node

 

Hi All

I have set up HTcondor in three computers by tarball and condor_config. The version is:

condor_version
$CondorVersion: 8.8.9 May 06 2020 BuildID: 503068 $
$CondorPlatform: x86_64_CentOS7 $

When I submit the jobs in central manager, which also configured as submit and execute, I found that the jobs are only executed in the central manager. They didn't execute in other two computers, It seems like that the three computers didn't connect to each other. However, when I check condor_status, I can see all three nodes in the pool. Could any one give some help?

Any advises are  appreciated!

Thank you very much!

 

Warm regards,

Xinjie Zeng

_______________________________________________
HTCondor-users mailing list
To unsubscribe, send a message to htcondor-users-request@xxxxxxxxxxx with a
subject: Unsubscribe
You can also unsubscribe by visiting
https://lists.cs.wisc.edu/mailman/listinfo/htcondor-users

The archives can be found at:
https://lists.cs.wisc.edu/archive/htcondor-users/