Re: [Condor-users] Newbie Install Question for 6.7.12

["Stephen Broughton" <buell_man@xxxxxxxxxxx>]

Thanks, I was stuck in the sbin and had not been looking in the bin.

I will get that updated and go from there.

----- Original Message ----- 
From: "Michael Yoder" <yoderm@xxxxxxxxxx>
To: "Condor-Users Mail List" <condor-users@xxxxxxxxxxx>
Sent: Wednesday, October 12, 2005 11:32 AM
Subject: Re: [Condor-users] Newbie Install Question for 6.7.12


> > I have a Linux Redhat Fedora 3 machine that I have installed Condor
> 6.7.12
> > using the rpm install.
> > 
> > I installed to /condor
> > 
> > This computer is on an isolated network with 9 other Fedora 3
> computers
> > that
> > will eventually become nodes.  There is no DNS or DHPC server on this
> > network, I am using a local host file list so that all the computers
> can
> > resolve to each other.
> > 
> > When I install the warning says that it is not able to identify the
> host
> > and to set the: NETWORK_INTERFACE=192.168.0.1
> > 
> > I have put that into the condor_config file which I have attached.  Is
> > this the best place to put it?
> 
> If /condor isn't part of a shared file system (I suspect it's not), then
> it'll only affect the machine that you put the change on.  You may want
> to see the discussion around RELEASE_DIR and LOCAL_DIR at:
> 
> http://docs.optena.com/display/CONDOR/RELEASE_DIR and
> http://docs.optena.com/display/CONDOR/LOCAL_DIR
> 
> (To actually answer you question, though, you'd usually want to put
> machine-specific settings like NETWORK_INTERFACE in your
> condor_config.local.)
> 
> > Then once I reviewed the condor_config file and modified it I ran
> > condor_master
> > 
> > The processes seem to start up correctly but they have a -f after
> them.  I
> > have not been able to find any reference to this and am wondering what
> it
> > means.
> 
> Don't worry about it.  The -f is an argument (added by condor) to the
> daemons.  
> 
> > [root@condor1 sbin]# ps -ef | egrep condor_
> > daemon    3454     1  0 Oct05 ?        00:24:41 condor_master -f
> > daemon    3314  3454  0 13:54 ?        00:00:00 condor_collector -f
> > daemon    3315  3454  0 13:54 ?        00:00:00 condor_negotiator -f
> > daemon    3317  3454  0 13:54 ?        00:00:00 condor_schedd -f
> > daemon    3320  3454  0 13:54 ?        00:00:12 condor_startd -f
> > 
> > This all looks like everything is running so I try to run the
> > condor_status
> > but I cannot find the command and I get an error when I try to run it.
> > 
> > [root@condor1 sbin]# condor_status
> > bash: condor_status: command not found
> 
> You need to either fully qualify condor_status:
> 
> /condor/bin/condor_status
> 
> or put it in your PATH:
> 
> export PATH=$PATH:/condor/bin
> export PATH=$PATH:/condor/sbin
> 
> > And where do I get the condor_compile files or install so that I can
> > compile and run the examples to test as jobs?
> > 
> > [root@condor1 examples]# make c
> > condor_compile gcc -o io.remote io.c
> > make: condor_compile: Command not found
> > make: *** [io.remote] Error 127
> 
> Same thing...put the condor binaries in your PATH.
> 
> Mike Yoder
> Principal Member of Technical Staff
> Ask Mike: http://docs.optena.com
> Direct  : +1.408.321.9000
> Fax     : +1.408.321.9030
> Mobile  : +1.408.497.7597
> yoderm@xxxxxxxxxx
> 
> Optena Corporation
> 2860 Zanker Road, Suite 201
> San Jose, CA 95134
> http://www.optena.com
> 
> 
> _______________________________________________
> Condor-users mailing list
> Condor-users@xxxxxxxxxxx
> https://lists.cs.wisc.edu/mailman/listinfo/condor-users
>