Hi,
I compiled different modules, but the simulation stops by giving
errors for the ruby config parameters:
failed assertion 'L2bank < RubyConfig::numberOfL2CachePerChip()/2' at
fn MachineID map_L1CacheMachId_to_L2CacheLocalBank(const Address&,
const MachineID&) in slicc_interface/RubySlicc_ComponentMapping.h:171
failed assertion 'L2bank < RubyConfig::numberOfL2CachePerChip()/2' at
fn MachineID map_L1CacheMachId_to_L2CacheLocalBank(const Address&,
const MachineID&) in slicc_interface/RubySlicc_ComponentMapping.h:171
At this point you might want to attach a debug to the running and get to the
crash site; otherwise press enter to continue
PID: 29724
I got similar error when I was using just one module. It would be a
great help if someone could point me to the where the problem might
be.
thanks a lot,
Mishali
On 10/9/06, Dan Gibson <degibson@xxxxxxxx> wrote:
Compile separate modules:
two make's with different DESTINATION=
Different configuration options:
Different scripts to run the simulations, eg:
ruby0.setparam... etc.
Mike Marty wrote:
> With 2 separate simulation jobs, sure.
>
> Either compile separate modules, or use the same module but specify
> different config options in Simics before starting simulation
>
>
>> -----Original Message-----
>> From: gems-users-bounces@xxxxxxxxxxx [mailto:gems-users-
>> bounces@xxxxxxxxxxx] On Behalf Of Mishali Naik
>> Sent: Monday, October 09, 2006 11:35 AM
>> To: Gems Users
>> Subject: Re: [Gems-users] Problem setting up runs with SNUCA and DNUCA
>> config
>>
>> I would like to have one run with SNUCA config, and another run with
>> DNUCA config (in parallel). Is it possible to have this set up?
>>
>> On 10/9/06, Mike Marty <mikem@xxxxxxxxxxx> wrote:
>>
>>> How don't get the question. You want results for 2 protocols (SNUCA and
>>> DNUCA) at the same time? You need to pick one config.
>>>
>>> Mike
>>>
>>>
>>>
>>>> Hi All,
>>>> I have been trying to set up runs with SNUCA and DNUCA
>>>> predictors simultaneously, but I haven't had any luck so far. At one
>>>> time, I can have runs with SNUCA configuration only or DNUCA
>>>> configuration only but not both. Is it because of the ruby config
>>>>
>> parameters?
>>
>>>> I am wondering if there is a work around this? I really would
>>>> appreciate any kind of help.
>>>>
>>>> thanks,
>>>> Mishali
>>>> _______________________________________________
>>>> Gems-users mailing list
>>>> Gems-users@xxxxxxxxxxx
>>>> https://lists.cs.wisc.edu/mailman/listinfo/gems-users
>>>> Use Google to search the GEMS Users mailing list by adding
>>>>
>> "site:https://lists.cs.wisc.edu/archive/gems-users/" to your search.
>>
>>> _______________________________________________
>>> Gems-users mailing list
>>> Gems-users@xxxxxxxxxxx
>>> https://lists.cs.wisc.edu/mailman/listinfo/gems-users
>>> Use Google to search the GEMS Users mailing list by adding
>>>
>> "site:https://lists.cs.wisc.edu/archive/gems-users/" to your search.
>>
>>>
>> _______________________________________________
>> Gems-users mailing list
>> Gems-users@xxxxxxxxxxx
>> https://lists.cs.wisc.edu/mailman/listinfo/gems-users
>> Use Google to search the GEMS Users mailing list by adding
>> "site:https://lists.cs.wisc.edu/archive/gems-users/" to your search.
>>
>
>
> _______________________________________________
> Gems-users mailing list
> Gems-users@xxxxxxxxxxx
> https://lists.cs.wisc.edu/mailman/listinfo/gems-users
> Use Google to search the GEMS Users mailing list by adding "site:https://lists.cs.wisc.edu/archive/gems-users/" to your search.
>
>
--
http://www.cs.wisc.edu/~gibson [esc]:wq!
_______________________________________________
Gems-users mailing list
Gems-users@xxxxxxxxxxx
https://lists.cs.wisc.edu/mailman/listinfo/gems-users
Use Google to search the GEMS Users mailing list by adding "site:https://lists.cs.wisc.edu/archive/gems-users/" to your search.
|